Often referred to as intumescent paint or intumescent coatings, fireproof coatings are used as passive fire resistance measures in structures and buildings. While the primary use of these coatings is for ‘fireproofing’ structures, they have added benefits by way of aesthetic and insulative properties.

When a thin-film intumescent is exposed to extreme heat, for example, in a fire, it significantly expands to form a thick foam boundary called a char. This char is quite thick and acts as an insulator, reducing the heating rate of the steel and preventing it from reaching the failure temperature, thereby, allowing occupants to evacuate and the emergency crew to take appropriate action.

However, it’s important to know that not all structural steel needs fire protection. The steel that does need protection will not have the same requirements for fire rating, with the fire rating requirement of a building determined by the design engineer or certifier with reference to building regulations. Some steel will be encased in partition walls and ceilings, some steel will need an FRL of 60/-/- and other steel members may need 120/-/-. So how do experts ascertain if the thickness of a coating will actually provide the protection it is designed to deliver? 

Currently, there is a myriad of coating thickness gauges suited for measuring the thickness of the fire rated coating applied to steel. In fact, there are different approaches for different stages of construction: During the spraying/application when the intumescent coating is still wet, spot checks use coating thickness gauges, which measure the wet film thickness to ensure the coating is thick enough. However, the actual measurement used for the purpose of system approval is ultrasonic equipment, which people in the painting industry use frequently. Building surveyors or certifiers do not accept the readings from the wet film thickness gauges; they will only approve the system by determining the thickness as measured through ultrasonic measurement. In other words, for all legal documents, ultrasonic is the way to go.

Thickness estimation and measurement utilising a coating thickness gauge in Australia occurs irrespective of whether applied on-site or off-site as long as the material is wet. However, prior to this, a certified structural engineer will need to determine the correct thicknesses for the coatings, which are to be applied (regardless of whether these are products such as vermiculite, Nullifire intumescent or other). With the specifications determined, an applicator can then apply the coatings to the required steel and the exposed sides identified as requiring application. But any coating system has its unique solid volume translation from Wet Film Thickness to Dry Film Thickness. It is critical to make sure that the right amount of coating is applied after the application job. 

Application inside the specified tolerances is best guaranteed through a process of ongoing and vigilant checking, and perhaps, not surprisingly, through elimination of surface deformities preceding application. For greatest accuracy, it is recommended that no readings are taken inside 25mm of the edge of an Ι-Beam or inside 25mm of the join of rib to web of an Ι-Beam segment when taking dry film thickness readings. However, while checking through the process is essential to ensure the materials are likely applied thickly enough, as per above, accurate measurement will only be achieved through an ultrasonic device.

Therefore, readings should be randomly taken over the remaining areas of a section with WFT gauges during application and ultrasonic equipment when dry. The frequency of measurements should be taken with regards to:

In ideal circumstances, for the purposes of compliance and to ensure accuracy of the fire protection of the completed work, each steel member requiring fire protection would be measured as per the above guidelines. In an ideal world, dry film thickness surveys should be completed by an independent third party; however, the applicator should also be undertaking this check throughout the process. Where thin-film intumescents (such as Nullifire, which is designed for structural steel) are applied (as opposed to technologies such as cementitious fire spray), independent signoff is particularly important for the purposes of achieving the warranties and certificates you need, so compliance to guidelines is important for applicators and for builders/site superintendents.

To ensure accuracy in the measurement process, please refer to these guidelines:

Fire engineering and intumescent applications are ever evolving, and highly technical fields. Our team at Permax exists to take the guesswork away for you, and help you achieve the best results and optimal outcomes. To learn more about fireproof coating for steel, consult the specialists at Permax today.

Discover products that suit your style and create a list of the items you like or want most.

Search through our latest projects and articles to find your inspiration for your next project

Join the community and give your insight into projects and news

Subscribe to get all the news, views, resources, comment and opinion on all things Architecture & Design delivered straight to your inbox.